 |
|
| 連結至中文版 | Issue No. 043 | January 2010 |
WiMAX Forum plans to begin certification testing in 2.3GHz, 5/10MHz, TDD profile by the end of January 2010On Dec. 30 2009, WiMAX Forum Cerification Working Group (CWG) has informed all Members that the CWG is very close to launching certification testing for 2.3GHz, 5/10MHz, TDD. Based on current status, CWG's expectation is to begin certification testing in this profile by the end of January 2010. Bureau Veritas ADT was starting for 2.3GHz, 5/10MHz, TDD test case validation to support WiMAX Forum CWG and test equipment vendor. Bureau Veritas ADT has also equipped all necessary test equipments and test cases for the certification testing. For more detail information, please do not hesitate to contact us. |
|
Bureau Veritas ADT worked with MediaTek, completing 1st WiMAX Forum Operator IOT CertificationBureau Veritas ADT, a leading WiMAX Forum Designated Certification Lab (WFDCL) for WiMAX Forum Certification Testing, announced that it has cooperated with MediaTek, a leading fabless semiconductor company for wireless communications and digital multimedia solutions, and supported MediaTek to acquire its first WiMAX Forum Operator IOT (Operator Interoperability Testing) & Conformance certificate. |
|
Wi-Fi CERTIFIED n released a newest TestplanWi-Fi Alliance released Wi-Fi CERTIFIED n new testplan version 2.0.4 to replace 2.0.3. There will be the usual 90 day transition period for the switch over. The 90 days expires on March 23, 2010. |
|
Wi-Fi Protected Setup has changed to the new test bedIt replaced the Intel station WM3945AGM1GEN with the Intel station 533AN_MMWG2 from the 11n approved test bed. The WPS test bed uses driver version 13.0.0.107. |
|
Wi-Fi CERTIFIED n has updated new softwareWi-Fi CERTIFIED n has updated new software. Version of the test bed equipment software Broadcom AP has changed from 5.10.128.05 to 5.22.69.2. |
|
Essential Reminder: 802.11n Draft 2.0 Grace Period has been extended through February 28, 2010Wi-Fi Alliance announced that due to overwhelming demand for the Wi-Fi CERTIFIED™ n test bed, the 90-day grace period for continuing use of the 11n draft 2.0 test plan and test bed has been extended through February 28, 2010. |
|
Essential Reminder: Single-stream access point devices are eligible for Wi-Fi CertificationWi-Fi Alliance announced that single-stream access point devices are eligible for Wi-Fi certification. These devices are not classified as Wi-Fi CERTIFIED n but will be tested according to the latest version of the Wi-Fi CERTIFIED n test plan: version 2.0.3 released through ECN 179. Testing can be performed at any Authorized Test Lab which has been qualified to perform Wi-Fi CERTIFIED n testing. |
|
Conformity with limits on radiated disturbance above 1GHzVCCI Council released the following information: " We will start enforcement of conformity with limits on radiated disturbance above 1GHz of products subject to conformity verification report filing on and after October 1, 2010. However, for one year until September 2011 it is up to each member to decide whether or not he will opt in conformity assessment tests above 1GHz. Nevertheless, however, let us ask you to positively go ahead and ship products conforming to the 1GHz+ requirement by filing conformity verification reports on and after October 1, 2010 as if there were no 1-year grace period. This is because VCCI runs its operation based on CISPR standards transposed to Japanese standard by the Information and Communication Committee, and July 2007 Japanese standard says implementation of 1GHz+ should start in 2010." |
|
IP Phone or ITE with VoIP function cannot get CCC certificationIn order to be consistent with the policies released from MIIT, CQC said that for VoIP Phone relevant products, they shall not be issued the CCC or CQC Certification. Vendors who apply for the certification of these products must be strictly aware of the definition instead of the name of the products. Once the sample was found that it is a VoIP Phone relevant product, it cannot be tested and CQC will contact the CQC engineer to terminate this application. VoIP Phone Definition: An independant phone equipment allowing telephone calls to be made over an IP network such as the internet. Each piece of voice data through these kinds of devices is digitized in to chunks and then sent across the Internet (in the case of public VOIP) to a destination server where the chunks are re-assembled. This technology also makes it possible to use VoIP to call into the Public Switched Telephone Network (PSTN) system. In order not to confuse other similar products, please check the below contents to make sure the certification category: The products not belonging to CCC and CQC's certification scope: Internet phone using using an Ethernet port and have sockets to connect one or more PSTN phones., IP Phone, VOIP gateway, etc. |
|
6 Bureau Veritas Test Lab are accredited by Vietnam MICBureau Veritas ADT announced that its test reports can be used for Vietnam approval submission from now on. |
|
Reminder: ANATEL new SAR requirement was in force on Dec 16th 2009 in BrazilSince Dec 16th 2009, the new Resolution 533 (new SAR resolution) has become mandatory as established by ANATEL. |
|
Reminder: The changing of Korea Customs Clearance law: ITE shall show product certificate when importingAccording to the Custom Act NO.2009-115, vendors have to provide KCC certificate to help their ITE products clearing South Korean custom from 1st January 2010. |
|
EU Updated EuP Directive to ErP DirectiveOn 21 October 2009, the European Council (EC) adopted a revision of the EuP Directive (hereinafter called "ErP Directive"). Modifications were made to the Directive in order to extend its scope. As a result, the Directive will now focus not only on “energy-using products” but will be extended to include all “energy-related products”, such as windows, water taps, shower heads, etc. Besides a wider scope, there is not much difference between these two directives. |
|
 |
|